The label is the law. Read your product's label before you mix or apply; the rates here come from the labels listed under Sources.
- Active ingredient
- Bifenazate
- Chemical class
- IRAC Group 20D, one of the mitochondrial complex III electron transport inhibitors acting at the Qo site, an energy-metabolism mode of action.[2]
- Mode of action
- IRAC Group 20D: Mitochondrial complex III electron transport inhibitors: Qo site[2][1]
- Signal word
- Floramite H&G Home and Garden Miticide: Caution[1]
Food plants and yearly limits
Never use it on fruits or vegetables grown for food. Fruit trees qualify only if they won't bear fruit for at least 12 months.[1]
The label's limit for ornamentals is 3 applications a year, or 1.5 pounds of active ingredient per acre. Its timing section allows a spray every 30 days.[1]
Where bifenazate fits in mite rotation
IRAC's Group 20 covers complex III Qo-site inhibitors. A footnote says the evidence that bifenazate acts there is strong, and some bifenazate resistance mutations give cross-resistance to acequinocyl, the Group 20B active.[2]
Where it is used
Spray as soon as mites appear. It mainly hits the moving stages of mites but also has some activity on spider mite eggs.[1]
It isn't systemic, so wet both the upper and lower leaf surfaces completely or mites will survive on the parts you missed.[1]
It won't control rust mites, broad mites or flat mites, so confirm which mite you have before buying.[1]
Test it on a few plants first. The label says it hasn't been shown safe on every ornamental, though no injury was seen at label rates in testing.[1]
Products and registrations
| Product | Registrant | EPA Reg. No. | Active % | Formulation | Signal word |
|---|---|---|---|---|---|
| Floramite H&G Home and Garden Miticide[1] | UPL NA Inc. | 70506-540 | 22.6% | liquid concentrate | Caution |
Label rates
| Product | Use | Pests | Rate |
|---|---|---|---|
| Floramite H&G Home and Garden Miticide | Ornamental plants, trees and shrubs, and non-bearing fruit trees | Spider mites, red mites, grass mites and other mite species | 0.25–0.5 tsp product per gallon of water[1] Mix 1/4 to 1/2 teaspoon per gallon and spray the foliage to full coverage with a hand sprayer. The label caps ornamentals at 3 applications a year. |
How to apply it, step by step
1. Protective gear
- The label lists no protective gear: it is harmful if swallowed and repeated skin contact can cause allergic reactions, so wash with soap and water after handling and before eating, drinking or using the toilet.[1]
2. Before you spray
- It controls spider mites, red mites and grass mites (mostly the active stages, with some effect on spider mite eggs); it doesn't work on rust, broad or flat mites.[1]
- Use it only on ornamental plants (bedding, flowering and foliage plants, perennials, trees and shrubs) and on fruit trees that won't bear fruit for at least 12 months, never on fruits or vegetables you'll eat.[1]
- Not every ornamental has been tested: try it on a few plants first.[1]
- It is toxic to fish and birds and moderately toxic to bees: don't spray while bees are foraging, spray in calm weather with no rain forecast for 24 hours, and keep it out of drains. Keep it away from heat and flame.[1]
3. Mixing
- Mix ¼ to ½ teaspoon per gallon of water in a hand sprayer.[1]
4. Applying
- Spray as soon as mites appear, covering the foliage completely, tops and undersides of leaves; it isn't systemic, so mites it doesn't reach aren't controlled.[1]
- On ornamentals, apply no more than 3 times a year, at least 30 days apart.[1]
5. After you spray
- Keep unprotected people and pets out of treated areas until the spray has dried.[1]
- Rinse the sprayer over the treated area rather than near a drain.[1]
First aid
- If swallowed, call a poison control center or doctor right away, have the person sip a glass of water if they can swallow, and don't induce vomiting unless told to.[1]
- The label's emergency line is Rocky Mountain Poison and Drug Safety, 1-866-673-6671; for spills, CHEMTREC at 1-800-424-9300.[1]
Storage, spills and disposal
Safety and environmental hazards
People
Signal word CAUTION: harmful if swallowed. Long or frequently repeated skin contact may cause an allergic reaction in some people, so wash well after handling.[1]
Pets
Keep unprotected people and pets out of treated areas until the spray has dried.[1]
Bees and pollinators
Moderately toxic to bees and other pollinators hit directly or exposed to residues on blooming plants. Don't apply while bees are foraging in the area.[1]
Fish and water
Toxic to fish, birds and estuarine or marine invertebrates. Keep it out of storm drains, ditches, gutters and surface water, and spray in calm weather with no rain due for 24 hours.[1]
Common questions
- How much Floramite H&G per gallon?
- One-quarter to one-half teaspoon per gallon of water, sprayed to full coverage on the foliage.[1]
- Can I use Floramite on tomatoes or fruit trees?
- Not on fruits or vegetables used for food. Fruit trees are allowed only if they won't bear fruit for at least 12 months.[1]
- Does bifenazate kill mite eggs?
- The label says it works mainly on the moving stages of mites but also has activity against spider mite eggs.[1]
Sources
- U.S. EPA Pesticide Product Label System, “Floramite H&G Home and Garden Miticide label, EPA Reg. No. 70506-540 (EPA-stamped, Sept. 11, 2024).” www3.epa.gov/pesticides/chem_search/ppls/070506-00540-20240911.pdf (accessed 2026-10-06)
- Insecticide Resistance Action Committee, “IRAC Mode of Action Classification Scheme, Version 11.5 (Feb. 2026).” irac-online.org/documents/moa-classification/ (accessed 2026-10-06)